What Is an Early Production Facility?
An Early Production Facility (EPF) is a surface processing installation designed to begin production from a discovered resource while the full field development is planned, financed, or awaiting regulatory approval. It is a deliberate compromise: a facility that is not optimised for the full field life, but that delivers early cash flow and reservoir data while minimising capital outlay and time to first oil.
EPFs are common in:
- Onshore discoveries where early cash flow accelerates field development financing
- Marginal fields where the full development economics are uncertain and early production de-risks the decision
- Fast-track offshore projects where a Minimum Facility Platform or MOPU is used ahead of a permanent installation
- Appraisal programmes where the EPF doubles as an extended well test to characterise reservoir performance
Understanding the difference between an EPF and a permanent facility — and designing accordingly — is what separates successful fast-track projects from costly over-engineered ones.
Core Design Philosophy
EPF design is governed by three overriding principles:
Simplicity. Every piece of equipment that is not strictly necessary adds cost, schedule, maintenance burden, and potential failure modes. An EPF should contain the minimum scope to safely produce, treat, and export the expected wellstream.
Speed to first oil. The commercial value of an EPF depends on early production. A design that delays first oil by three months to include a "nice to have" feature has destroyed more value than it created.
Reversibility and upgrade path. Where possible, the EPF design should anticipate the permanent facility — using the same pipeline right-of-way, the same injection scheme, the same process philosophy. Bridges to the permanent facility are far cheaper to include at EPF design stage than to retrofit later.
Typical EPF Scope
A basic onshore EPF for dry gas and condensate typically includes:
Wellstream Reception
- Inlet separator (test separator with allocation metering, or a dedicated test loop)
- Wellhead control and ESD valving
Primary Separation
- Two or three-phase production separator
- Design pressure and temperature matched to wellhead flowing conditions at low reservoir depletion (early life)
- Generous retention time margins for emulsion-prone crudes
Compression (if required)
- Wellstream or gas compression to meet export or re-injection pressure
- For EPFs, reciprocating compressors are often preferred over centrifugal — wider turndown, faster delivery, lower installation complexity
Produced Water Treatment
- Basic hydrocyclone and degassing vessel for offshore
- API separator or Induced Gas Flotation for higher water cut or tighter discharge standards
- Note: water cut typically rises over EPF field life — design for the end of EPF life, not the beginning
Gas Export or Flaring
- Export compression and metering where gas sales are available
- Flaring system sized for full well test flow and worst-case emergency depressurisation
- In many early production scenarios, gas is flared or re-injected — gas sales infrastructure often follows permanent facility development
Utilities and Safety
- Power generation (diesel gensets on onshore EPFs; minimise electrical complexity)
- Chemical injection (scale inhibitor, corrosion inhibitor, demulsifier, H₂S scavenger if required)
- Flare and relief system to API 520/521
- ESD and F&G system — simplified relative to permanent facility but fully compliant
Modularity: The Key to Fast-Track Delivery
The most effective EPFs are designed as skid-mounted, factory-built, and pre-tested modules. Modular construction:
- Reduces site work — hazardous open-site construction is the main schedule driver and cost uncertainty in remote locations
- Enables parallel construction — the process module, power module, and utilities module can be built simultaneously in different fabrication shops
- Simplifies pre-commissioning — skids can be function-tested at the fabrication facility before transport
- Enables relocation — if the EPF is to be moved to another location after the permanent facility takes over, modular design makes this practicable
The trade-off is detailed co-ordination between modules during design. Interface management — mechanical interfaces, pipe connections between skids, electrical and instrument interconnects — must be rigidly controlled from the early design stage. Interface errors discovered on site are expensive.
Sizing for the Right Case
EPF sizing must consider field life dynamics:
Liquid rates. Wellstream liquid rates often decline over time. Size the separator for early-life maximum rates with adequate turndown to maintain separation efficiency at low rates.
Water cut. Water cut almost invariably increases over field life. Design the water handling system for the end of EPF life — the period with the highest water rate and potentially the tightest discharge specification.
GOR. Gas-oil ratio may increase over field life as reservoir pressure declines. Ensure the gas system can handle the maximum GOR case without constraining production.
Reservoir pressure decline. As reservoir pressure falls, wellhead flowing pressure drops, and wellstream temperature decreases. Check that the separator design pressure is appropriate for early life (high WHP) and that the compression system handles late-life (low WHP) conditions.
Common EPF Engineering Mistakes
Over-engineering to permanent facility standards. An EPF does not need the same redundancy, design life, or code compliance level as a 25-year permanent installation. Applying full permanent facility standards to an EPF that will operate for three to five years is a common and expensive error.
Under-sizing the water handling system. Early production water rates are typically low, so projects underinvest in water handling. When water cut increases — as it always does — the facility is constrained, and costly modifications are required.
Inadequate flaring provision. A flare system sized only for normal operation creates safety and environmental problems when an emergency depressurisation or well test requires full-field flaring. Always size the flare for the credible maximum simultaneous release.
Ignoring site utilities. Power, water, waste, and communications infrastructure in remote onshore locations are frequently underestimated. They are not complex, but they are essential — and long-lead in some geographies.
Project Management for Fast-Track EPF Delivery
Fast-track EPF projects succeed with:
- Parallel engineering and procurement — long-lead items (pressure vessels, compressors, generators) must be ordered on preliminary datasheets, not after final design
- Weekly vendor progress calls — fabrication shop progress must be tracked and problems resolved in real time, not discovered at factory acceptance testing
- On-site construction supervision — a competent construction manager on site, full-time, from mobilisation through handover
- Pre-commissioning at the fab shop — pressure tests, loop checks, and functional testing before shipment catch problems where they are cheapest to fix
Conclusion
An EPF designed with the right philosophy — simple, fast, fit for its actual operating life — delivers early cash flow without disproportionate capital expenditure. The engineering discipline required is not less demanding than a permanent facility; it is differently demanding. The skill is in knowing what to include, what to exclude, and how to sequence delivery to achieve first oil on schedule.